Draper SC1 Manual de Instruções descarregar pdf (Página 60)

SUN AND WIND SENSOR V1.l and SUN SENSOR SWITCH V4 by Draper Page 5 of 9

Three Intermediate Positions on Sun, use default settings (S+7+7 > C# > C10 > 08):

Four Intermediate Positions on Sun, use default settings (S+7+7 > C# > C10 > 09):

Sun Thresholds and Levels

User selection of "level” using Sun Sensor Switch:

If the user presses the appropriate buttons on the Sun Sensor Switch to set the Sun threshold, all thresholds are

moved up or down appropriately. All pending sun actions are lost when a level is selected.

Example: Default sunrise setting is 68 with 3 increment, sunset is 48 with 3 increment.

The sunrise LEDs at low setting indicate 68,71,74,77,80, and at high setting 80,83,86,89,92.

The sunset LEDs at low setting indicate 48,5 1,54,57, Mi, and at high setting 60,63,66,69,72.

At low setting with 2 intermediate positions Open23 will be sent at 71, Close23 at 77, Close ALL at 80, Close23 at

57, Open23 at 5 1, and Open ALL at 48.

At medium setting the numbers change to: Open23 @ 77, Close23 @ 83, Close ALL @ 86, Close23 @ 63,Open23

@ 57, and Open ALL @ 54.

Setting Sun Thresholds

To set the sun thresholds you must enter the two-digit low threshold number and then enter the two digit increment.

For example, entering 40 as the low sunset threshold with an increment of 04, sets the low 5 thresholds from low to

high to: 40,44,48,52,56, and the high 5 thresholds to 56,60,64,68,72.

This example would be done with the following sequence: S+7+7 > C# > C5 > 04 > 0 10 > 0 10 > 04

The following sequence must be completed to change any thresholds:

1- Press S+7+7 > C#, the GREEN programming LED must light.

2- Press C4, the LED will blink off then GREEN, and you are setting sunrise thresholds (or press C5 for sunset).

3- Press 0 1-10 to select the 10's of percent of the low threshold (01 0 selects O), the LED will blink RED then

GREEN.

4- Press 01-10 to select the 1's of percent of the low threshold, the LED will blink RED then GREEN.

5- Press 0 1-1 0 to select the 10's of percent of the increment, the LED will blink RED then GREEN.

6- Press 0 1-10 to select the 1's of percent of the increment, the LED will blink off and then be GREEN.

If bad numbers are entered, the LED will flash GREEN & RED a few times and then be GREEN and the original

thresholds are UNCHANGED and the accessory is still in program mode but must get a close command next.

Errors include:

-Entering a starting threshold where low sunrise would not be more than low sunset.

-Entering an increment of 0.

-Entering a threshold and increment where the high threshold (Low + 8" Increment) would be > 99 percent.

-Entering a threshold and increment where a sunrise would not be more than the associated sunset.

-Programming either sunrise or sunset thresholds automatically sets the threshold to high (default).

If you are not using the Sun Sensor Switch to change between the thresholds, then the high threshold set is the only

one used. The programming sequence MUST still be completed.

After installation, be sure to select a Sun Sensor Delay of at least 10 minutes.

Page 60 of 120

1 2 ... 55 56 57 58 59 60 61 62 63 64 65 ... 119 120

Sem comentários

Draper SC1 Manual de Instruções Página 60