Draper SC1 Manual de Instruções descarregar pdf (Página 44)

Please Note

➀ Make sure power is disconnected before installing controls.

➁ SPGC4 is a line voltage control, designed to individually operate 4

motors, activated by Low Voltage input commands.

➂ SPGC4 enclosure is 8" x 8" x 4".

➃ The Main Disconnect and Branch Circuit Protection shall be provided by

installer.

➄ Maximum surrounding air temperature 50° C.

➅ Use copper conductors rated 75 degrees Celsius or higher only, 18-

12AWG.

Please Note: This device has not been evaluated for reliability to the

Standard for Tests for Safety-Related Controls Employing Solid-State

Devices, UL 991 and therefore not considered suitable for entrapment

protection.

Wiring Instructions

™

SPGC4 Control by Draper

If you encounter any difﬁ culties installing/wiring your IntelliFlex control, call your dealer or

Draper, Inc., Spiceland, Ind., (765) 987-7999; or fax (765) 987-7142.

Part Number C156.060

Inserting wire into spring terminal

➀ Open spring terminal by inserting screw-

driver into upper opening.

➁ Insert wire into lower opening.

➂ Remove screwdriver.

Electrical Speciﬁ cations

Input:

Data: +5v AC BUS Commands

Low Voltage: Dry Contact—0v AC

Line Voltage: 115v AC +/- 10%

Output:

115VAC Largest Motor 1FLA, 4FLA Total

E258229

Please Note: Connect Ground

wires as noted on enclosure

IntelliFlex

Eye

Port

To Switch,

splitter or

other input

device

IntelliFlex

Neutral

AC (115V AC)

IntelliFlex

Data cable

from Aux Port

to Eye port of

next SPGC4

Aux

Port

Aux

Port

Aux

Port

Aux

Port

Eye

Port

Eye

Port

Dry

Contacts

Dry

Contacts

Dry

Contacts

Motor

Black (Dir)

Red (Dir)

Neutral

Red (Dir)

Black (Dir)

Neutral

Red (Dir)

Black (Dir)

Motor

Black (Dir)

Red (Dir)

Neutral

Please Note:

Connect all

Ground wires to

ground block

provided.

Eye

Port

Max of 100 feet

of cable

between

controls, or

control and

input with

circuit

board.

Fabric un roll ing from back of

roller (standard)

Fabric unrolling from front of

roller (reverse roll)

Interior

side

Interior

side

Right hand motor

(Standard)

Black—Up

Red—Down

Left hand motor

Black—Down

Red—Up

Right hand motor

(Standard)

Red—Up

Black—Down

Left hand motor

Red—Down

Black—Up

All connection wires must conform to the motor manufacturer’s

recommendation and prevailing electrical codes. The switch and control

system wires should be at least 24 AWG and no larger than 18 AWG.

Please Note:

All input devices (low voltage LED switches, IR eye, RF receiver) which

connect to the Eye jack must be connected using electrically straight 4-

conductor modular cable (RJ11). This means colors do not cross over: blue

leads to blue, orange to orange, etc. (see diagram below)

If you use standard telephone cable, you must ﬁ rst remove one connector,

turn it over and re-attach, to ensure that the cable is electrically straight (see

diagram below). Standard phone cable is 26 AWG.

Yellow

Red

Green

Black

Yellow

Red

Green

Black

Yellow

Green

Red

Black

Yellow

Green

Red

Black

Standard Telephone Cable

(Before, will not work)

Telephone Cable After

(Electrically Straight-will work)

Yellow

Green

Red

Black

Yellow

Green

Red

Black

Electrically Straight Data Cable

Using Telephone Cable

Page 44 of 120

1 2 ... 39 40 41 42 43 44 45 46 47 48 49 ... 119 120

Comentários a estes Manuais

Sem comentários

Draper SC1 Manual de Instruções Página 44

Comentários a estes Manuais

Manuais e produtos relacionados com não Draper SC1